bout time

Move the tow eye back towards the rear of the board more, even just an inch or two, and maybe higher by an inch or two as well. Also drill some small holes in the bottom of the boards towards the rear and fill them with lead. I used old sinkers. Then epoxy over the lead to seal the holes. This will make the boards sit lower in the water and “bite” more adding them to pull harder and better ‘Bout Time Mike

Water levels are up due to the IJC , spring runoff, and rain. They are not releasing anymore water until the water in Canada starts residing. It has risen nearly 8-10” last week and going up more. Not predicting as bad as 2017 but a close second ‘Bout Time Mike

I have a total of 8 cannon dual axis. 6 are mounted inside Traxstech tracks and the other 2 are mounted into a Berts track. As stated above all interchangeable ‘Bout Time Mike

Run a 8 gauge wire directly from your motor to the battery ground. Depending what side battery is on the easiest place to run a jumper is circled below. I had the same issue and replaced the starter and solenoid and is still was doing it. I didn’t see (think) any of my grounds looked bad. I added a “jumper” from the exhaust riser post to my negative battery post and it has worked ever since. Easier to try this before you try to access your starter ‘Bout Time Mike

Pm sent ‘Bout Time Mike

Stainless Steel Taylor Made Triple Fender Holder. Holds 3 fenders up to 9” in diameter. Retails for over $200 Asking $75 or BO Pick up around Syracuse or Fair Haven ‘Bout Time Mike

theres on in the classified thats rigged without the tracks

Looks like an old Pfleuger. Search for “Pfleuger 5 hook minnow” and some will come up. Looks to be worth a couple hundred $$ ‘Bout Time Mike

Mine is a 2352 but similar layout. I run tracks on the sides with 3 rod holders per side. Riggers mounted in each corner. The center is either a Chute rod holder or 3rd rigger. ‘Bout Time Mike

‘Bout Time Mike

‘Bout Time Mike

Channel side has the most damage ‘Bout Time Mike

The west side pier at Fair Haven is being torn apart from the high water and storms.... https://www.facebook.com/688939275/posts/10157556560604276?sfns=mo ‘Bout Time Mike

came across this on Youtube. growing up around the salmon river and other northern tribs ive seen alot of fishing pressure but this may beat them all

Sold Sent from my iPhone using Lake Ontario United mobile app

Sold ‘Bout Time Mike

Going to be another bad year for flooding. I stopped at FH this weekend and the water is already 14" higher then the same date from 2017 which was the last flood. There has been more snowfall during late February and early march this year versus 2017 and will only add to higher levels once its melts......

not crazy but unexpected. Late July trolling off FH in 8-12 FOW for bass with my parents and caught this guy. Super fun on Ultra light Spin Tackle

NEW PRICE ............

Your planer line will definitely interfere with your rods, especially on turns and waves. One of the best options is to move (or install) a second pulley as far forward as possible, even all the way to the bow. Attached are two pictures of my setup. Ive changed from the bow pulley to the one on the hardtop for ease of use and both work great

Older model cannon low profile swivel base. Bought used as a spare and never used it. $35- includes shipping to lower 48 ‘Bout Time Mike

(2) Diawa Great Lakes Sealine 47 LC One has approximately 800-900’ of 1x7 wire Other one is empty Both reels have upgraded Power Handles and upgraded drags by Tuna Toms. These have been sitting in my cuddy as spares and have not been used much at all. Always stored inside boat and in the house during the winter since I’ve owned them. $100 - includes shipping to lower 48. PayPal as F/F Check or Money Order

Ive used them before with no problems and liked how easy it was for removal. The only thing i did to mine was add some electrical tape around the shaft because mine were a tad loose in the rod holder.