VooDoo

Price drop. $200. For all Sent from my SM-G930V using Lake Ontario United mobile app

Bump Sent from my SM-G930V using Lake Ontario United mobile app

Ttt Sent from my SM-G930V using Lake Ontario United mobile app

Whats the measurements on these? For one seat or two? Sent from my SM-G930V using Lake Ontario United mobile app

I have 4 Big Jon dual axis rod holders on 2 pedestals. Good working condition. These were used as diver holders but could serve multiple uses since they are adjustable. Will fit several track systems or can be bolted on. $125 pair or $225 for all. You pay shipping. These go for close to $200 for one pair. Sent from my SM-G930V using Lake Ontario United mobile app

Wanted to post these earlier but internet has been down. Fished with a buddy out of Bald Eagle on the 23. East in 100 fow. 5 for 5 on teenage kings. Many many lakers But what really stood out were these three lakers. (Which were all released.) Wire diver back 280 and a 400 copper, both with meat. 2 over 20 lbs Sent from my SM-G930V using Lake Ontario United mobile app

Is this sold? Sent from my SM-G930V using Lake Ontario United mobile app

Collar has run, point, and locate modes. Adjustable in multiple levels of stimulation. Collar and control both are rechargeable . Charger included. Spare charging port covers. Spare anodes for collar. Tester. Manuals and hard case. Good working condition. $230 shipped. Paypal Sent from my SM-G930V using Lake Ontario United mobile app

Sorry about the upside down pics, tried to turn them Sent from my SM-G930V using Lake Ontario United mobile app

HiFished out of Bald Eagle. 10th and 11th. 10th. Sloppy conditions and bad Karma. Issues with riggers and got some bad 20 lb fluro leader. New, name brand. 5 break offs on kings. Managed to land 2 kings and a couple lakers. Took a massive hit on a flasher and meat rig behind an inline board. Deep diving stick also also broke off. Mainly Spoon bite tho. 11th. Much better conditions. Riggers fixed. Leaders replaced. About equal numbers of lakers and kings with 1 Atlantic . All spoon bite. Earlier 45 to 60 fow. Riggers and divers down 20 to 35' Later in day 20 to 30 fow. Spoons down 15 to 25' on riggers and divers. Sea sick waddler spoon hot, as well as other glow spoons. Sent from my SM-G930V using Lake Ontario United mobile app

Wont last very long. Sent from my SM-G930V using Lake Ontario United mobile app

After 20 years in the bird hunting business its time to move on. Selling my training equipment. I have a remote control bird launcher (pigeon size), e collar, Quail harness, vhs training video, .22 cal blank starter pistol, 15' check cord. Spare annodes, antenna, batteries and tester. I lost the battery cover for the controller but cover is held in place with velcro, and works fine. Control operates the collar and the launcher. Everything has been tested and is in good working condition. $200 shipped. Will accept Paypal.. Sent from my SM-G930V using Lake Ontario United mobile app

SOLD Sent from my SM-G930V using Lake Ontario United mobile app

I have two Big Jon 6" Pedestals with 4" plates. Base plates have a couple knotches that don't afftect anything. They were used to secure track adapters. $75 shipped. Pm please. Will accept PayPal. Sent from my SM-G930V using Lake Ontario United mobile app

Was originally going to go with pvc boards over top of the carpet. As fate would have it, I found a Caliber bunk wrap kit on ebay for a price I couldnt refuse. Took the boat to a local lake and launched it. With the help of a buddy we installed the bunk wrap and end caps on the existing boards over top of the carpet. About a half hour job. Took the boat for a test run came back and loaded on the trailer. Must say it reduced the friction by about 50%. Made for a much easier winch job. All stainless screws were included. Sent from my SM-G930V using Lake Ontario United mobile app

The sharkskin was mixed into the last coat of epoxy. Then applied with a roller. You can make it as rough textured as you like. Sherwin Williams 646 macro epoxy is used on offshore oil rig platforms. I figured if it would hold up in that environment it would work for my boat. I too was thinking of going with vinyl but after I saw how the sharkskin came out figured I didnt need vinyl. If for some reason I dont like the epoxy, I can always add the vinyl later. Good luck Sent from my SM-G930V using Lake Ontario United mobile app

Hey Don, I'll lend all the moral support that you need. Sent from my SM-G930V using Lake Ontario United mobile app

I doubled the cutting board, making it 1" thick. Screwed it together with counter sunk screws from the backside with marine sealant around the edges. Drilled and countersunk four corners and drilled the transom. Sealed the holes with 5200. With that totalscan ducer at over $300, dont know if I would trust adhesive 100%. Sure to break something if it would break loose and be slapping around back there if you were under power. I dont plan on taking the pads back off anyway. Plenty of room to mover ducers around if needed. Sent from my SM-G930V using Lake Ontario United mobile app

Also about the most economical route as well. Sent from my SM-G930V using Lake Ontario United mobile app