-
Posts
934 -
Joined
-
Last visited
Content Type
Profiles
Forums
Events
Gallery
Store
Everything posted by Hachimo
-
Mexico
Hachimo replied to Logger Gen II's topic in New York Fishing Reports - Lake Ontario (South Shore)
Boats all good. Quick fix at the dock. Batteries and corrosion happens Just screwed me up for the shotout. Screens full of fish down 100 in 160 At first light and coupdnt get to them we fished this evening 6pm to 8:30. 2/2 one 8lb steel and 7lb king on spoons on dipseys 220 back. Back at the dunes at first light tomarrow -
Mexico
Hachimo replied to Logger Gen II's topic in New York Fishing Reports - Lake Ontario (South Shore)
Was also out from the dunes this morning Went 4/5 nothin over 7lb. Had a bad battery in the new boat and it caused a whole lotta havoc! No riggers. Then no electronics. Then finally lost starboard engine and that was enough. I stuck it out cause I was in the shootout. Fished 160 and screen was loaded with marks. All fish came on junk lines one on meat rest were spoons. Heading back out now. -
Mexico
Hachimo replied to Logger Gen II's topic in New York Fishing Reports - Lake Ontario (South Shore)
-
Mexico
Hachimo replied to Logger Gen II's topic in New York Fishing Reports - Lake Ontario (South Shore)
-
I just recently got a fishhawk. Prior I just fished the marks. I’d stack my riggers in different depts so I have a good portion of water colum covered. If I noticed lots of fish in a certain depth I would set a rigger 5-10ft above them. After getting a fishhawk the way i fish the marks didnt really change much, but the speed at the ball blew my mind. Gps would say 2.3 and I would b 1.3 at ball. If ur fishing the Marks and not getting bites, try speedin up/slowin down or S turns. That also worked well for me
-
Wanted looking to buy a magma fish cutting board for boat
Hachimo replied to dpiazza22's topic in Classifieds - Buy, Sell, Trade or Rent
-
Wanted looking to buy a magma fish cutting board for boat
Hachimo replied to dpiazza22's topic in Classifieds - Buy, Sell, Trade or Rent
-
Wanted looking to buy a magma fish cutting board for boat
Hachimo replied to dpiazza22's topic in Classifieds - Buy, Sell, Trade or Rent
-
Wanted looking to buy a magma fish cutting board for boat
Hachimo replied to dpiazza22's topic in Classifieds - Buy, Sell, Trade or Rent
-
Wanted Fish cleaning table for boat
Hachimo posted a topic in Classifieds - Buy, Sell, Trade or Rent
Lookin to buy a little flat stand that slides right into the rod holders in the back of the boat. I see most charter boats have them and it’s definitely convienent to have. Not lookin to spend crazy money one. If someone has on layin around let me know a price trou PM thanks. mike -
Mexico 7/18
Hachimo replied to Hachimo's topic in New York Fishing Reports - Lake Ontario (South Shore)
-
Sodus pro am
Hachimo replied to rdebadts's topic in New York Fishing Reports - Lake Ontario (South Shore)
-
Mexico 7/18
Hachimo replied to Hachimo's topic in New York Fishing Reports - Lake Ontario (South Shore)
-
Mexico 7/18
Hachimo replied to Hachimo's topic in New York Fishing Reports - Lake Ontario (South Shore)
Slow bite this far, but didn’t get rods in untill 7:30. My phobe died last night so told the wife to set the alarms for 4:30. Well I got wokin up by my dog lickin my face at 6:30 1/1 so far 7lb ish king on white meat rig on dipsey out 180 setting 2. I’m a little handicap using only one rigger two dipseys two coppers. I’m out infront of hoghrocks. Picked the one up in 200fow. Workin my way in 150Fow now -
Took my last trip with my Trophy this evening. Hauled the new boat from Point Breeze to Mexico and got the at 6pm. Had the itch, so left it hooked to the truck and jumped in the old boat. Rods in at 6:30pm and setup in 180Fow Went an hour without a bump, then had a screamer on the deep rigger (blue UV FF) parked at 90. 21lb released it and missed another. Pulled gear at a 7:45 and headed in to start swapping gear to the new boat. Never thought I would spend 2.5hrs and still have a mess in both boats First light I will be out with the new rig. Hopefully I can get the bolts I need to mount the new riggers. If not I’m sure dipseys and junk lines will get it done.
-
Wanted Cannon mag 10 Hs or newer
Hachimo replied to Hachimo's topic in Classifieds - Buy, Sell, Trade or Rent
Baha 280 weekender -
Kind of in a pickle. Got a new boat and its all setup minus downriggers. Lookin to fish on it tomarrow and cannot find new cannons in stock. I’m traveling from point breeze to Mexico this afternoon, so if someone has one or a few for sale and ur on the way I will be more then happy to take them off your hands. I’m lookin for newer style riggers. Not mag 10a’s shot me a PM thanks Mike
-
New Boat!!! Who has new cannon mag 10’s in stock?
Hachimo replied to Hachimo's topic in Open Lake Discussion
-
New Boat!!! Who has new cannon mag 10’s in stock?
Hachimo replied to Hachimo's topic in Open Lake Discussion
-
New Boat!!! Who has new cannon mag 10’s in stock?
Hachimo replied to Hachimo's topic in Open Lake Discussion
-
New Boat!!! Who has new cannon mag 10’s in stock?
Hachimo replied to Hachimo's topic in Open Lake Discussion
-
It finally happened. Found the boat Ive been drooling over the past few seasons and picking it up Saturday Morning in point breeze and heading to Mexico! The owner is keeping his 3 riggers as they r brand new and goin on his new boat, but gave me a killer deal as the boat is equipped with everything else. Bein I planned on spending a little more for the boat I have the extra nickels and want to put 3 new riggers on. I like the cannon mag 10’s and want to buy 3 this weekend but every shop in pulaski dont have any in stock. Anyone know if thereS any places along the south shore that would have 3 mag 10’s in stock thanks. mike
-
Sounds odd to me. I always put my dipseys out first then riggers then send a copper or two off each side on inline boards. Never had an issue. Is it possible maybe u were turning a little when letting out the copper? Definitely sounds like a mess. Especially with a FF