Flygaff

Wow, where do you buy your props. The most I’ve ever paid for a prop was 500. And that was a Merc 4 blade SS prop for my twin 200 optis

Sizing props is tricky. Weight of the boat will determine a lot. I have half a dozen Suzuki props out in my shed from trying different one that didn’t work

My guess would be a 13 to get you closer to the correct rpm range

I have a G3 185f with a 24 by I5 trolling motor. I use 2 135 AH batteries. They last all day without any problem.

I ordered two of the 120 ah batteries. They were out of stock so they sent me the 135 ah version. I have been running them for about a year now with my 24 volt XI5. Very happy. They can run for days

Thanks, I ran the boat with the 140 on it for the first time yesterday. 34/35 mph. I thought it would run a bit faster. I only ran it for a few minutes cause I was on a 10 hp lake. I think with playing with the trim and a little weight distribution I believe I may gain a few more mph. I was at 5900 rpm. Mace is 6300. A balancing act for sure.

Can’t wait to get out there. Our striped bass fishing gets underway in a few weeks. I just troll around the bay for them. I think I will be able to troll all day for them for about ten gallons of fuel. I hate to drop my new boat into to saltwater buts it’s gotta happen some day

Well the twin 9.9/20 did not work. I just mounted a Suzuki 140. Keeping one 9.9 for trolling. I have not run the boat yet. My guess is I will be just over 40 mph give or take. I will know in a few days. Now I wonder if I can run this 15-20 miles off the beach. I have a lot of offshore (75+miles) with my now gone 25 center. Have to check my fuel burn. It hold 35 gal. Looks like I wont get to the tuna, but sharks should be in range.

Looking for Used Suzuki 4 stroke Outboard 25 inch shaft 90HP, 115 HP, or 140 HP Low hours and Good Price. Found what I need but I don't want to drive to NC for it if possible. I am In NJ

2022 Suzuki 9.9/20 HP Outboard new 2022 9.9 outboard with 3 hours run time. Converted to a 20 HP with the 20 HP ECU and an Inlet plate Perfect condition I also have the adapter to use it a a 20 inch or 25 inch shaft. Elec start/Power Tilt Remote unit Includes Davis Fin Wire Harness Fuel tank No Controls 5 year warranty Perfect Condition Engine is in New Jersey. $3200

That's a great price. If it were a 20 inch I would take it. Good luck with the sale. I'm sure it will sell fast. + it is a very easy swap to a 20 HP with just 2 parts

I go to other lakes and rivers. That's why I would like it to go a bit faster

Lake restrictions of 9.9 hp. They don’t seem to care how many you hang on the transom. I upgraded them to 20 hp each. I am keeping my eyes open for a 90 or 115. The boat could be ordered with a 90 or 115 and the hull is rated to 200

Yea, the hull weighs 1700, 2 engines at 120 each and four group 31 AGMs. Lots of weight. I will keep messing with it. I will get it going a bit faster. I just need 3-4 MPH to be satisfied

This was a dealer rigged boat with the twin 8s. The only engines ever on the boat. I just don't know why they would have added 320 pounds to the stern. The logs in memory on the hummingbird says on multible routes 15 MPH and up the 18. Strange. I will try distributing the weight and trying again. I do know i'm underpowered. just trying to squeeze a little more speed out of her